Attention: Guests by accessing CRO, you agree to the site terms. Please read the terms of CRO Click Here

« previous next »
Pages: 1 2 [3] 4

Author Topic: Bone Stock Build  (Read 17951 times)

0 Members and 1 Guest are viewing this topic.

Offline jworacing

  • Contributing Members
  • Series Owner
  • ******
  • Posts: 1257
  • Cause we suck at hockey
    • JWO Racing
Re: Bone Stock Build
« Reply #30 on: September 06, 2011, 06:20:20 AM »
The cage will be mounted to 1-1/2 X 3 X 1/8" wall Rectangle tubing. The sleeving was all done with .120 wall 1-1/2" as this particular cage is actually made with .120 wall. She is a bit heavy but it will be stiff for sure. We cut the cage with a bigass pipe cutter so it actually gives you a decent prep for welding. If you tack your sleeve before joining you end up with a nice open root with the sleeve as a backing plate. This gives you full penetration on your butt joint. This will be as strong as the original tubing was. If done correctly there is no need to worry about it being any less safe than any other joint on the cage

Linkback: https://www.canadianracingonline.com/smf/index.php?topic=14028.msg97075#msg97075
Logged
"The winner ain't the one with the fastest car, it's the one who refuses to lose."
- Dale Earnhardt

CanadianRacingOnline.com

Re: Bone Stock Build
« Reply #30 on: September 06, 2011, 06:20:20 AM »

Offline jworacing

  • Contributing Members
  • Series Owner
  • ******
  • Posts: 1257
  • Cause we suck at hockey
    • JWO Racing
Re: Bone Stock Build
« Reply #31 on: September 18, 2011, 02:54:29 PM »
I'm coming with some pics for yesterdays and today's work...hang on!! and does anybody have any Cavalier rims 5X100mm?

Stock rocker rail where we are going to reinforce for cage mount and side impact


Reinforcement rail in place along rocker rail welded to the floor and the rocker rail box section


Drivers side rail ready to weld in


This section where it is doubled up will be where the vertical bar of the cage will be attached to


This plate is welded to the the rear strut tower and a brace to the halo joint of the cage will go here


The cage will be going in next

Linkback: https://www.canadianracingonline.com/smf/index.php?topic=14028.msg97560#msg97560
« Last Edit: September 18, 2011, 04:34:49 PM by jworacing »
Logged
"The winner ain't the one with the fastest car, it's the one who refuses to lose."
- Dale Earnhardt

Offline racingwrench

  • Series Owner
  • *****
  • Posts: 594
Re: Bone Stock Build
« Reply #32 on: September 18, 2011, 08:20:31 PM »
Logged

CanadianRacingOnline.com

Re: Bone Stock Build
« Reply #32 on: September 18, 2011, 08:20:31 PM »

Offline bornagain

  • Chaos Car Driver
  • Rookie Driver
  • ***
  • Posts: 76
Re: Bone Stock Build
« Reply #33 on: September 18, 2011, 09:57:41 PM »
Quote from: jworacing on September 18, 2011, 02:54:29 PM
I'm coming with some pics for yesterdays and today's work...hang on!! and does anybody have any Cavalier rims 5X100mm?

i got some rims offa 96 sunfire.  they shud fit... make an offer, also if u need any other parts let me know the cars just gonna go to scrap after i pull the cage as it has a blown engine now.

Linkback: https://www.canadianracingonline.com/smf/index.php?topic=14028.msg97603#msg97603
Logged

Offline bornagain

  • Chaos Car Driver
  • Rookie Driver
  • ***
  • Posts: 76
Re: Bone Stock Build
« Reply #34 on: September 19, 2011, 09:25:27 PM »
Logged

Offline bornagain

  • Chaos Car Driver
  • Rookie Driver
  • ***
  • Posts: 76
Re: Bone Stock Build
« Reply #35 on: September 20, 2011, 08:35:24 PM »
i think 14" but ill check and c for sure tmrww

Linkback: https://www.canadianracingonline.com/smf/index.php?topic=14028.msg97749#msg97749
Logged

Offline jworacing

  • Contributing Members
  • Series Owner
  • ******
  • Posts: 1257
  • Cause we suck at hockey
    • JWO Racing
Re: Bone Stock Build
« Reply #36 on: September 25, 2011, 11:32:25 AM »

The vertical bar passes in to the rectangle tubing for increased resistance to shearing forces


That horizontal bar passes thru the fire wall to the strut tower


This bar holds the cage by bracing it against the rear shock tower

Linkback: https://www.canadianracingonline.com/smf/index.php?topic=14028.msg97959#msg97959
« Last Edit: September 25, 2011, 03:32:44 PM by jworacing »
Logged
"The winner ain't the one with the fastest car, it's the one who refuses to lose."
- Dale Earnhardt

Offline Dougy109

  • Series Owner
  • *****
  • Posts: 980
  • Known by my brothers as 'Bones"
Re: Bone Stock Build
« Reply #37 on: September 27, 2011, 06:00:06 PM »
Logged
Not an expert, just tried it, refused to listen to conventional thinking, broke all the parts trying

Offline jworacing

  • Contributing Members
  • Series Owner
  • ******
  • Posts: 1257
  • Cause we suck at hockey
    • JWO Racing
Re: Bone Stock Build
« Reply #38 on: September 27, 2011, 09:11:23 PM »
We welded the roof back on it last night but couldn't do much cause of the rain. We gunna go back at it tomorrow

Linkback: https://www.canadianracingonline.com/smf/index.php?topic=14028.msg98058#msg98058
Logged
"The winner ain't the one with the fastest car, it's the one who refuses to lose."
- Dale Earnhardt

Offline jworacing

  • Contributing Members
  • Series Owner
  • ******
  • Posts: 1257
  • Cause we suck at hockey
    • JWO Racing
Re: Bone Stock Build
« Reply #39 on: October 09, 2011, 12:15:53 PM »
This is one ugly car


The filler panels on the windshield area are so we can utilize lexan we had kicking around that wasn't quite big enough

Seat Mount



The dash cluster is required or the car doesn't run I'm told something to do with theft system



Right side door welded back on



Linkback: https://www.canadianracingonline.com/smf/index.php?topic=14028.msg98329#msg98329
Logged
"The winner ain't the one with the fastest car, it's the one who refuses to lose."
- Dale Earnhardt

Offline jworacing

  • Contributing Members
  • Series Owner
  • ******
  • Posts: 1257
  • Cause we suck at hockey
    • JWO Racing
Re: Bone Stock Build
« Reply #40 on: October 09, 2011, 12:26:01 PM »
Logged
"The winner ain't the one with the fastest car, it's the one who refuses to lose."
- Dale Earnhardt

Offline jworacing

  • Contributing Members
  • Series Owner
  • ******
  • Posts: 1257
  • Cause we suck at hockey
    • JWO Racing
Re: Bone Stock Build
« Reply #41 on: October 10, 2011, 06:51:30 PM »
THis car is for sale and we're asking $1200 for it. if you are interested give me a shout


]

Linkback: https://www.canadianracingonline.com/smf/index.php?topic=14028.msg98374#msg98374
« Last Edit: October 10, 2011, 08:13:30 PM by jworacing »
Logged
"The winner ain't the one with the fastest car, it's the one who refuses to lose."
- Dale Earnhardt

Offline Dougy109

  • Series Owner
  • *****
  • Posts: 980
  • Known by my brothers as 'Bones"
Re: Bone Stock Build
« Reply #42 on: October 13, 2011, 05:38:21 AM »
Logged
Not an expert, just tried it, refused to listen to conventional thinking, broke all the parts trying

Offline jworacing

  • Contributing Members
  • Series Owner
  • ******
  • Posts: 1257
  • Cause we suck at hockey
    • JWO Racing
Re: Bone Stock Build
« Reply #43 on: October 13, 2011, 09:45:34 AM »
I can't race due to fiscal restraints...meaning I'm broke. I'm gunna sell the car off and maybe build another for next year. Perhaps at that point I can purchase the necessary equipment to be able to compete. Sad but true :(

Linkback: https://www.canadianracingonline.com/smf/index.php?topic=14028.msg98439#msg98439
Logged
"The winner ain't the one with the fastest car, it's the one who refuses to lose."
- Dale Earnhardt

Offline streetstocker33

  • Series Owner
  • *****
  • Posts: 614
Re: Bone Stock Build
« Reply #44 on: October 13, 2011, 10:29:34 PM »
Quote from: jworacing on October 13, 2011, 09:45:34 AM
I can't race due to fiscal restraints...meaning I'm broke. I'm gunna sell the car off and maybe build another for next year. Perhaps at that point I can purchase the necessary equipment to be able to compete. Sad but true :(
what's missing? there isn't much to them, can't be much missing lol what's left? we might have stuff.

Linkback: https://www.canadianracingonline.com/smf/index.php?topic=14028.msg98455#msg98455
Logged
Pages: 1 2 [3] 4
« previous next »
 

HTML ezBlock
site stats
Powered by EzPortal